众所周知,进口淮安NSK轴承是许多机械设备的核心部件,在机械设备中起着不可替代的作用.轴承会受到周围环境的影响,使轴承受到不同程度的损坏,因此作为外部设备进口轴承也应给予相应的重视.

As we all know, imported Huaian NSK bearings are the core components of many mechanical equipment, and play an irreplaceable role in mechanical equipment. Bearings will be affected by the surrounding environment, so that bearings will be damaged to varying degrees, so as an external equipment imported bearings should also be given appropriate attention.

在常规检查过程中,如发现轴承油量不足,应从注油口或油位孔注油.注意油位孔或油位已达到量规的极限.

In the course of routine inspection, if insufficient oil is found in the bearing, oil should be injected from the oil injection port or oil level hole. Note that the oil level hole or oil level has reached the limit of the gauge.

经检查发现,当淮安NSK轴承需要更换机油时,应先将其排出.卸油温度应达到40-50℃,在扰动下卸油.只有这样,脏油才能被彻底排放和清洁.这样,在润滑油排放前,应先启动滚轮的温润滑油,使热油快速流出,使箱内杂质容易与润滑油混合排出.

After inspection, it is found that when Huaian NSK bearings need to replace oil, they should be discharged first. The unloading temperature should reach 40-50 C and unload oil under disturbance. only in this way can dirty oil be thoroughly discharged and cleaned. In this way, before discharging the lubricating oil, the warm lubricating oil of the roller should be started to make the hot oil flow out quickly, so that the impurities in the box can easily be mixed with the lubricating oil and discharged.

但对于驱动桥、轮行星减速器和励磁油腔,由于其壳体的外露部分是旋转的,在检查油位或卸载、加油时,需要打开一个思想装置,将油孔的位置调整到合适的位置.

But for the drive axle, wheel planetary reducer and excitation oil chamber, because the exposed part of the shell is rotating, when checking the oil level or unloading, refueling, it is necessary to open an ideological device to adjust the position of the oil hole to the appropriate position.

还应注意,在油位检查或灌装时,油位可以达到油孔边缘所指示的油位.

It should also be noted that during oil level inspection or filling, the oil level can reach the oil level indicated by the edge of the oil hole.

在使用变频器的变速风扇中,破坏性的电流很可能流过轴承.这可能导致轴承过早失效和风扇关闭.使用绝缘淮安NSK轴承可以防止破坏性电流引起的故障.与其它绝缘方法相比,这种轴承结合了轴承的功能和电气绝缘的功能,是一种经济的解决方案.轴承内环或外环的外表面采用普通工艺涂覆氧化铝,具有绝缘效果,不受高温、水汽和化学物质的影响.

In variable speed fans using transducers, destructive currents are likely to flow through bearings. This may lead to premature bearing failure and fan closure. Insulated Huaian NSK bearings can prevent faults caused by destructive current. Compared with other insulation methods, this kind of bearing combines the functions of bearing and electrical insulation, and is an economical solution. The outer su-ce of bearing inner ring or outer ring is coated with alumina by common process, which has insulation effect and is not affected by high temperature, water vapor and chemical substances.

轴承的性能和运行精度与标准非绝缘轴承相同.不需要额外的预防措施.

The performance and operation accuracy of bearings are the same as those of standard non-insulated bearings. No additional precautions are required.

圆锥轴承的装配是整个装配过程中的一个难点.首先是传动系统的装配.锥齿轮的预加载方式和预加载力直接影响锥齿轮的传动状态和整个传动系统的传动精度.

The assembly of tapered bearings is a difficult point in the whole assembly process. First is the assembly of the transmission system. The bevel gear pre-loading mode and pre-loading force directly affect the transmission state of bevel gear and the transmission accuracy of the whole transmission system.

性能保证了变速器的使用寿命.如果预紧力过大,可根据承载能力、速度和工况合理设置轴承预紧力.电力消耗甚至会导致过热.如果预紧力过小,滚动体之间的间隙和内环和外环将发生在负载的作用下,将导致传动轴跳跃和移动,减少传输的准确性,增加噪音,影响齿轮啮合,在严重的情况下损坏齿轮和轴承.

The performance ensures the service life of the transmission. If the preload force is too large, the bearing preload can be set reasonably according to the load-carrying caPACity, speed and working conditions. Electricity consumption can even lead to overheating. If the pre-tightening force is too small, the clearance between the rollers and the inner and outer rings will occur under the action of load, which will lead to the jump and movement of the transmission shaft, reduce the accuracy of transmission, increase noise, affect gear meshing, and damage gears and bearings in serious cases.

文章来自:淮安SKF轴承 -

Article from: Huaian SKF Bearing -

文章来自:淮安INA轴承 -

Article from: Huaian INA Bearing -

文章来自:淮安NSK轴承

Article from: Huaian NSK Bearing

QQ:

电话:0

手机:/